See Translation
$5.86
4.8
15 reviews
Series 3 AA Aluminium Alloy Battery Holder Case Box for Flashlight
Voucher:
Promotion:
Support COD payment Warehouse & Fee
SelectCN-099:Ship between: Jul 08 - Jul 10
Reviews (15) View More
Neil
Feb 01,2016
- 1. Solidly built. 2. Perfectly sized to take my Eneloops without crushing them. Any standard AA or unprotected button top 14500 cell should fit. Flat top cells and protected 14500 cells are unlikely to work, however. 3. Can be dismantled with a 2mm hex bit, making it easy to modify. Be careful to reassemble correctly if you do this. Some of the PCB pads are connected by tracks within the PCB, so you'll short out your cells if you get it wrong! 3A. You could bypass the springs and PCB tracks with flexible wire if you needed a high current battery carrier. 3B. You could also convert it into a Parallel 3 AA Holder by moving one of the springs so that they're all at one end and wiring the PCB pads in parallel at each end.
Description
Feature:
Holding 3 pieces of AA battery. This holder both can protect battery circuitry from damage and components from leakage. Use this battery holder to make a convenient, stable way for batteries. It will be best replacement for LED flashlight torch
Note:
1. Batteries are not included.
2. Plus and minus marking on the holder are reversed. Please take care when installing in flashlight.
Holding 3 pieces of AA battery. This holder both can protect battery circuitry from damage and components from leakage. Use this battery holder to make a convenient, stable way for batteries. It will be best replacement for LED flashlight torch
Note:
1. Batteries are not included.
2. Plus and minus marking on the holder are reversed. Please take care when installing in flashlight.
Specification
General | Accessory type: Holder |
|---|---|
Dimensions and Weight | Product weight: 0.020 kg Package weight: 0.06 kg Product size (L x W x H): 6.9 x 2.8 x 2.8 cm / 2.72 x 1.10 x 1.10 inches Package size (L x W x H): 8 x 4 x 4 cm |
Package Contents | Package Contents: 1 x Battery Holder |
View More
Recommended Products
Sponsored Products
loading...
loading...
loading...
loading...
4.8 *****
- 12
- 3
- 0
- 0
- 0
- All ( 15 )
- ( 4 )
- ( 1 )
Neil
Feb 01,2016
- 1. Solidly built. 2. Perfectly sized to take my Eneloops without crushing them. Any standard AA or unprotected button top 14500 cell should fit. Flat top cells and protected 14500 cells are unlikely to work, however. 3. Can be dismantled with a 2mm hex bit, making it easy to modify. Be careful to reassemble correctly if you do this. Some of the PCB pads are connected by tracks within the PCB, so you'll short out your cells if you get it wrong! 3A. You could bypass the springs and PCB tracks with flexible wire if you needed a high current battery carrier. 3B. You could also convert it into a Parallel 3 AA Holder by moving one of the springs so that they're all at one end and wiring the PCB pads in parallel at each end.
- Suggestion:
- 1. As others have noted, the polarity markings are reversed on some of these. Before you use them, put some cells in and check the polarity with a voltmeter. 1A. If you need to, remark them with the correct polarity (a silver Sharpie is good for this). 1B. Alternatively, take them apart with a 2mm hex bit and swap the black plastic end caps over. 2. Over time, the positive pads on the PCBs may be subject to wear, because they're copper and therefore softer than the steel cell buttons. It might be worth tinning the pads with solder, especially if you happen to be modifying one of these anyway.
Daisy
Sep 03,2014
- Not a lot to say, thankfully. I mean, it's a battery holder for flashlight. Works as advertised. Arrived with no problems, I put batteries in, hooked it up to a small propeller and everything worked as it should. Good product and pretty cheap, can't complain about anything!
- Suggestion:
- No.
binelas
Oct 25,2016
- High quality 3 AA Aluminium Alloy Battery Holder it is very solid,batterys fits well inside,no problems so far
- Suggestion:
- none
colinisom
Jun 15,2015
- Really well built and great materials. Decently built AA battery carriers are so hard to find at a reasonable price. Thank You GearBest for supplying these :-)
- Suggestion:
- All were built Backwards, thus the review title. Had to change all the + and - marks on the end plates with white marker, to avoid blowing up any flashlights! Thankfully I'd checked them all with a Volt Meter before fitting in anything :-) Slight raising of the screws on the ends, not a problem for my uses, but some have had to tighten them down for clearance purposes.
Hans
Feb 23,2016
- the Battery holder ist exactly described. The aa battery fits very well- i tested also many kinds of protected 14500 Lithium aa- tey fit well.
- Suggestion:
- for me there is no contra for this item
Nonn
Apr 01,2016
- I have it very firmly. It is long life every day even if I replaced it.
- Suggestion:
- Slightly high price.
Cherry
Oct 06,2014
- Just as described by the seller and nice for small projects. Great service. Good delivery.
- Suggestion:
- No.
Cherry
Sep 04,2014
- Exactly as advertised. Everyone should buy one or two! Very good battery holder.
- Suggestion:
- No.
recsler85
Mar 26,2015
- Nice build quality. Works as expected.
- Suggestion:
- So far, I am very pleased with this battery holder. No cons.
rczegeny
Apr 13,2015
- solid build quality, it does the job it is designed to do
- Suggestion:
- i do not have any negative to say about this product, it works as its supposed to
View More